High port density Advanced Ethernet Converter with up to 4 x 10/100BaseTx user ports, with performance monitoring

Pandatel’s advanced Ethernet converter ET-CA is a device that provides media conversion between multiple Ethernet electrical signals (10/100BaseTx) and Ethernet fibre signals (100BaseFX).

The ET-CA Ethernet converter has 2 x 10/100BaseTx interface ports and a single100BaseFX port for optical transmission. For higher density applications in a central site, a concentration variant of the ET-CA with 4 x 10/100BaseTx interface ports can be specified. Optionally, an additional 100BaseFX port can be requested. With double the capacity, the cost of racks and agents are reduced making it a cost effective investment.

Elementary 10/100Mbps Ethernet Converter.LAN-to-LAN connectivity - Converts between 10BaseT/100BaseTx interface and 100BaseFx interfaces

ET-CE Media Converters are highly reliable, cost-effective media converters providing media conversion between Ethernet electrical interfaces (10 Mbps, 10/100Mbps, 100 Mbps) and Ethernet optical interfaces (100 Mbps). In that way you can greatly extend the transmitting distance of your Ethernet network. ET-CE Media Converter can transmit data at wire speed with low latency. The transmission distance of 100 Mbps optical interface may reach up to 40 km.

Modular High-Speed Gigabit Ethernet Converter and Modem for the Access area

ET-CG Ethernet converters offer flexible universal solutions for the connection of Ethernet networks with broadband IP backbone systems. The ET-CG supports three Ethernet bandwidths 10/100/1000 Mbps. Therefore they are applicable for all types of Ethernet systems and solutions, and as such represent safe investment options for clients.

Fiber Optic Back-up System, appropriate for redundant optical fibre lines in cases of emergency

The intelligent fibre optic back-up system FOBUS functions similarly to a converter, but is additionally equipped with a redundant fiber optic line. This line will automatically take over data transmissions if an error occurs within the main line. Thus, one of the lines (the main line) is continuously used for data transmission purposes, whereas the additional back-up line can be used for management and control/monitoring purposes.

Asynchronous industrial interfaces up to 128kbps

The modems of the product group FC-A transfer asynchronous data with a maximum speed of 128 Kbps. The standard interfaces used in the industry can be transformed by the FC: RS485, RS422 and RS232. The Fibre Optic Modem FC-A is designed for different cable types (multimode / singlemode) and LED components. Due to this modular design transmission distances of up to 30 km can be achieved.

Fiber Optic Mini Converter for industrial applications

The FMC is a compact and cost efficient solution for transmission of asynchronous signals in any environment. This space-saving alternative to any other oversized converter card can be plugged directly into the DB-25 connector of external devices. The signal will be converted to fibre to bridge distances up to 80 km! Power for this unit can be fed via the DB-25 plug or via an external power supply.

Typical applications are the connection of external devices in several buildings of one complex to a central system: Hospitals, universities, enterprises, industrial companies, … every campus-like application is possible.

Video monitoring applications in factories, tunnels, traffic surveillance

The Fibre Optic Video Converters FV have been specially designed for surveillance systems requiring seamless transmission over long distances.

The Fibre Optic Video Transmitter FV-T (camera side) converts video signals into light signals. These light signals are transferred over optical fibres to the Fibre Optic Receiver FV-R which reconverts the light signals into electrical signals and transfers them to the attached units (e. g. monitors). The units of the product group FV operate according to the standard VBS 1 Vpp with 75 ? termination. This specification fits typical surveillance requirements.

Simultaneous transmission of Video and Data signals

The units of the product group FV-C allow the transmission of video and data signals via fiber optic, e.g. video signal and camera control (pan, tilt and zoom).

Using the FV-C units guarantees all the advantages of fiber optic technology: electrical insulation, galvanic separation, tap proof as well as long transmission distances. The units are prepared for the use of a WDM FibreDoubler, i.e. the costs for fiber installation can be reduced significantly. The Fibre Optic Converters FV-C are well suited for area and building surveillance, gate, tunnel, traffic and access control (e.g. airports, refineries etc.). According to the requirements transmission distances of up to 20 km can be reached.

Digital video & data converter from copper to fibre optic

Pandatel’s new DV and DV-C series show state-of-the-art technology for transmission of video signals. Standard analogue video signals can be taken to be converted to either Multimode or Singlemode digital fibre optic signals. Via light the video signal can bridge distances up to 80 km before it will be re-converted. The DV-C additionally transports control data for the camera on a bi-directional basis. Thus commands from control center to each camera can be sent, and the acknowledgements from the cameras will be received back as well. The DV-series can also be used in industrial environments with highest demands on quality and reliability.

Fractional 4-wire modems

4-wire baseband modems supporting data rates up to 2048kbps. Large range of interfaces: X.21, V.24, V.35, BRI, G.703

Flexible 4-wire transmission with HDB3 coding, a truly cost effective solution

The 4-wire baseband modem GM-F is used for connecting terminals operating at data rates of n x 64 kbps (n= 1, 2, 3 ... 31). The device functions as a bit rate adapter and supports the frame formats according to ITU-T G.704. When the framing is not active, the device is working as transparent2 Mbps converter (n= 32). GM-F modems are therefore applicable for non-switched connections and internal links. On the terminal side, interfaces such as X.21, V.35, V.36 and Ethernet Interface are supported. The device is available as a standalone or as a rack mount card. The Ethernet Bridge supports VLAN and10/100BaseT autosensing.

GM-E offers LAN connectivity to E3/T3 data rates

GM-E devices connect LANs and set up Internet connections. The GM-E is a flexible solution with a broad functional range, allowing for the conversion of Ethernet-formatted data into standard formats at data transmission rates within the range of E3/T3. Small companies can connect their LANs in different locations via radio networks or directly to the Internet, to use its data without any limitations of bandwidth or terrestrial lines.

2-wire baseband modems

— Data rates:
      BM-P: up to 128 Kbps
      BM-Z: n x 64 Kbps up to 2.048 Kbps

— Interfaces:
      BM-Z: X.21, V.24, G.703, V.35, V.36, 10BaseT,
              BRI, Uk0
      BM-P: X.21, V.24, G.703, V.35, V.36, 10BaseT

2-wire G.SHDSL transmission at its best

The BM-G is a 2-wire G.SHDSL modem for long distance data transmission via copper lines of up to 12 km. The line data rate ranging from 64 to 2312 kbps can easily be adjusted in steps of n x 64 kbps via the VT100 or SNMP management. The interface data rate can be set insteps of n x 64 kbps from 64 kbps up to 2312 kbps (resp up to 2048/1544kbps for E1/T1). Additionally, unframed G.703 operation is supported.